Predisporre di un server TFTP e di un cavo ROLLOVER. Dopo il primo prompt, da Hyperterminal su COM, dare CTRL-BREAK o CTRL_PAUSE. Fatto questo, seguiamo la seguente procedura.
System Bootstrap, Version 12.2(1r)XE2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 2001 by cisco Systems, Inc.
SOHO 77 platform with 16384 Kbytes of main memory
rommon 1 > confreg 0x2142
rommon 2 > restart
System Bootstrap, Version 12.2(1r)XE2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 2001 by cisco Systems, Inc.
SOHO 77 platform with 16384 Kbytes of main memory
rommon 1 > "IP_ADDRESS=10.23.25.69"
rommon 2 > "IP_SUBNET_MASK=255.255.255.0"
rommon 3 > "IP_DEFAULT_GATEWAY=10.23.25.1"
rommon 4 > "TFTP_SERVER=10.23.25.12"
rommon 5 > "TFTP_FILE=soho70-oy1-mz.122-13.zh8.bin"
rommon 6 > confreg 0x2102
You must reset or power cycle for new config to take effect
rommon 7 > tftpdnld
IP_ADDRESS: 10.23.25.69
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 10.23.25.1
TFTP_SERVER: 10.23.25.12
TFTP_FILE: soho70-oy1-mz.122-13.zh8.bin
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n: [n]: y
Receiving soho70-oy1-mz.122-13.zh8.bin from 10.23.25.12
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Copying file soho70-oy1-mz.122-13.zh8.bin to flash.
Erasing flash
................................................................
Programming flash .............................
rommon 8 > reset
System Bootstrap, Version 12.2(1r)XE2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 2001 by cisco Systems, Inc.
SOHO 77 platform with 16384 Kbytes of main memory
program load complete, entry point: 0x80013000, size: 0x39963c
Self decompressing the image :
################################################################ [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) SOHO70 Software (SOHO70-OY1-M), Version 12.2(13)ZH8, RELEASE
SOFTWARE (fc1)
Synched to technology version 12.2(14.5)T
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Tue 13-Dec-05 23:43 by ealyon
Image text-base: 0x800131C0, data-base: 0x80640450
CISCO SOHO 77 (MPC855T) processor (revision 0x301) with 15360K/1024K
bytes of memory.
Processor board ID JAD058217VT (62738350), with hardware revision 6FE6
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)
boot-start-marker
^
% Invalid input detected at '^' marker.
boot-end-marker
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
Router>ena
Router#reload
Router con0 is now available
Press RETURN to get started.
Come potete ben vedere, il router è tornato a vivere. ;-)
